The Hub

Hi all! I was wondering if anyone knew how to source a Stelling tailpiece or knew of what would fit? I have a White Star model that came in with one that's broken. I tried their website and I just get errors and I understand Geoff Stelling retired a few years back. Images

I have a Favilla Classical guitar on the bench, in for a bridge reglue. This is a low to mid-range classical guitar, made circa 1960, and it's an heirloom guitar for the customer, he basically wants it back in playing shape. The story is that he went away on vacation, and when he returned the bridge had delaminated from the top and took a fair amount of finish with it. It also appears that someone attempted to glob on superglue at some…

Good evening folks, lately I'm experiencing some sanding methods/mechanism frustration. Can't explain better than look like I'm regressing at doing it. The only thing changed in my building routine is that I'm currently using a CNC (I haven't used one for some years) for both bodies and necks. I have no problems with necks, but sanding bodies has become incredibly frustrating, specially around the edges. While I keep improving my c…

Here You'll seehere pin tip sized bubbles. Nitro finish. It got hot in a case. They'll need a light amagolmater mixture applied to melt'm back into the surface. Im looking for advice on the recipe for said amagolmater....Straight retarder? Im not sure if Id need lacquer in the mix that I apply....Thank you! Colin O'Brien LittleCreek Instrument Repair, Nashville. Images

I have a 2024 Les paul in fine shape. One thing i’m curious about is that the nut and truss rod spacer appear to have been modified but there are no finish marks in the cavity to suggest a repair. is this a normal factory install adjustment and have other folks here come across it in les pauls?

Hi There, I've seen a number of jigs, Some seem like they might work with specific size frets but we all know that even same sized frets have some variances depending batch and where on the line it came off the spool. No matter how i do it I seem to scrape the bottom of the fret trying to make it perfectly flush. I've considered using small rotary round burr or cylinder and only touching the tang so if it does go to deep its…

HEy FOlks. Ive Been using a really old timer and reostat control, with a separate thermometer, on my heat blanket set up for a while. Its worked, but id like to be a bit more mindless about it if possible. Does anyone have suggestions for heat blanket controllers that have a digital readout and built in temp control sensor?

YouTube video on how to Glue a Cracked Top Brace With Hot Hide Glue 

Hey all, Just wanting to get an idea of what peoples experience has been like buying bone blanks from S.F. International. I placed an order back in late February, close to $500 AUD, and 3 months on, they are still yet to ship to me in Australia. I was told over a month ago that the order was ready to ship and since then, I keep getting told "Dispatch tomorrow". Anyone else have this experience and still got their order?

Hello all- We have a job opening in the repair shop here at elderly. Looking for someone professionally trained, with 5+ years of experience preferred, but any and all are welcome to apply. Send resumes and inquiries to [email withheld] Tell him you saw the post on the looth group!

Well, I am pulling my hair out here... just did a compression fret job on a 2017 D18 Authentic 1939. Neck had severe excess relief, so I pulled the frets, planed the board flat, and got to work....done this a handfull of times, so I wasnt expecting anything out of the ordinary...... I got a handful of frets in, checked my relief by stringing up the guitar, and decided I need to keep pushing, so I got a full set of frets in and som…

Anyone know what glue type is appropriate for a Martin DXME fretboard extension to secure it to the plastic laminate top (or whatever it is)? I have one on the bench that has broken loose, and I’m not sure what to use. I tried contacting Martin, but they won’t help since I’m not an authorized Martin repair shop. 🫤 Thanks!

Hi all, I am a newer guitar tech and after dozens of repairs this particular Simon & Patrick Luthier Cedar top SP6 acoustic dreadnought from the 90-ies with a bolt-on maple neck has been an incredible challenge. It came with a maxed out and stuck truss rod with a considerable up bow in the neck, extremely low saddle with barely any string break angle, so it needed a neck reset. Later on I figured out that it also has a pretty dras…

Video on Top Mapping a Master Built Robert Ruck Classical Guitar with a Magic Probe- at the end I talk about the magic probes benefit to some repair work.

I picked up a set of these chisels a couple years ago at an estate sale. They were in a very sorry state but had clearly been used and loved. I gave them a good cleaning and sharpened just the smallest one, which took a very nice edge. I'm debating sharpening the rest in order to sell them along with my Narex chisels (which I haven't loved) and replacing them all with a couple Lie Nielsen chisels only in the sizes I really use. Anyone h…

Gah! I need help wiring Lollar Monoliths to coil split each pup at their own 2 way mini switch...client brought it in wired to a card ( based on rough drawing ) said he "tested it"....I had to clean up his wiring and soldering some...both pots, 3-way and 2-way switches are functioning but I get a weak signal when plugged in....what am I missing here? I redrew it ( nicer drawing ) with the black hots going to the 3-way ( swapped with gre…

Hey guys, does anybody know of a good alternative to mixol? I use it in lacquer for mixing opaque colors and it's great but I've been on the lookout for something more affordable and haven't had much luck. Wondering if anybody here knows of anything. Thanks!

Hi Everyone, I've got this knock off Les Paul in the shop right now and the wiring is a rats nest as you can see in the picture. Does anyone know which of the pictures from the guitar wiring bible what would apply to this guitar? The volume pot is an issue that I may just try to clean but if I do decide to tackle all of the wiring I’m curious to know which diagram I should be working with. Thanks in advance! Images …