The Hub

This guitar appears to have been assembled with urea formaldehyde glue, which is insoluble in water and doesn’t melt at any reasonable temperature. It is definitely not hide glue or resorcinol.The neck pocket is not under a fret slot. Luckily, very little glue was used to assemble the neck and it was all on the cheeks of the tenon and the neck came off rather easily using a combination of the StewMac heat rod and foam cutters, with smal…

Let me start with this; I'm trying to find the root cause of difficult fret wire installation of two different SM fret wires. I've spent a lot of time gathering dimensions and experimenting with techniques wich could cause the problem. I enlisted the help of a colleague who arrived at a similar poor performance. His solution was to glue the fret ends/ beat the frets in. My "rather" is to find the root cause so I don't have to go thr…

Since most of us fix or make guitars, we have probably heard something about the cease and desist letters Fender has sent out concerning the Stratocaster. I thought I would offer some thoughts. As always, caveat emptor. There are three basic ways to protect intellectual property under Federal law. Patent, trademark, and copyright. Each protects different things, and has different underlying legal theories. Lets begin with pate…

Straight Frets in Austin has an excellent full-time position opening up soon. The job pays by the job, and equates to $70-85K a year for a tech that does: *neck resets *structural repairs *bridge making/reglues *refrets *headstock breaks with splines/airbrush We work on about 1,350 guitars a year (about 28-30 a week) and have had work shipped in from 22 different states at this point. We also teach setup classes on…

I am working on a neck reset on a Washburn Parlor - SN 283552. I have read that the 28 in the SN indicates that is was built in 1928, but the owner thinks based on her research that it was built before 1920. I am assuming a dovetail joint and that I can get into the neck joint for steaming by drilling into the 13th fret slot, but if anyone knows differently please let me know. The fingerboard extension has already separated slightly…

Hi There, I've seen a number of jigs, Some seem like they might work with specific size frets but we all know that even same sized frets have some variances depending batch and where on the line it came off the spool. No matter how i do it I seem to scrape the bottom of the fret trying to make it perfectly flush. I've considered using small rotary round burr or cylinder and only touching the tang so if it does go to deep its…

Well, I am pulling my hair out here... just did a compression fret job on a 2017 D18 Authentic 1939. Neck had severe excess relief, so I pulled the frets, planed the board flat, and got to work....done this a handfull of times, so I wasnt expecting anything out of the ordinary...... I got a handful of frets in, checked my relief by stringing up the guitar, and decided I need to keep pushing, so I got a full set of frets in and som…

Hi all, I am a newer guitar tech and after dozens of repairs this particular Simon & Patrick Luthier Cedar top SP6 acoustic dreadnought from the 90-ies with a bolt-on maple neck has been an incredible challenge. It came with a maxed out and stuck truss rod with a considerable up bow in the neck, extremely low saddle with barely any string break angle, so it needed a neck reset. Later on I figured out that it also has a pretty dras…

I'm restoring an old parlor guitar. I have just discovered that it plays 20 cents sharp. Thats not in and of itself a mystery, usually. This guitar however has exactly the same distance from the nut to the 12th fret, and from the 12th fret to the "saddle" which is now a small shim under the two E strings both are 12 3/32"...with room in front of the bridge pins to finesse the location of the saddle slot, which I have not routed yet) I s…

I bought the StewMac fret jaws and am hoping to sell the heavy press. I can't imagine shipping it but if you're in Northwest Alabama come by and buy this from me. Buddy Guy is playing here at the end of the month and we have Jason Isbel and the Drive By Truckers playing here for Shoals Fest some time this summer.

I have a Kalamazoo made epiphone with the most extreme fingerboard ramp I have seen. I have the neck dead straight from 1st fret to body joint and get a 1/16 of gap when I run a straight edge from 1st fret to the last fret. The frets average .040" but someone leveled the extension and those frets are half the height. Does anyone have any suggestions for flattening the extension. Clamping a block on it? If I level the board during a r…

A new one for me... joint is pretty much centered between 12th and 13th.

Hi there! Working on a Squire Vintage Modified Jag. relevelled and crowned the frets. Lovely job. Set the relief and action to factory spec. So far so good. With a capo on the first fret, I set the string radius at the saddles to 9.5" using an under-string radius gauge, everything lined up nicely... ...but when I measured the action of all the strings along the 14th fret using my digital nut slotting gauge (expecting a unifo…

Hey everyone, I'm a technician at a music production school in London. As the most 'guitariest' technician on staff, I've become the de facto guitar maintenance person. A big part of my work is taking a look at each guitar once a week. Usually my "routine" is to check action and intonation, making adjustments if needed, then cleaning/polishing. The thing I struggle with the most is getting strings feeling good. We use D'Addario…

Just sharing some info to procrastinate my nth attempt at getting this thing together. and some venting. If you get one of these in with electronic issues, estimate high. Customer brought in a Gretsch Rally in pieces that he picked up from the last repairman (who died), and just wants it to play. Minor binding repair and a weirdly-angled zero fret were relatively easy to deal with. The dead electronics are the main problem.…