The Hub

For those of you who regularly do semi-hemispherical frets -- how long do you make your frets? Specifically for a bound fretboard (although I suppose this would apply to either bound or unbound) do your frets come up a little short of the outside edge of the binding? And if so, how much gap do you leave? I did my first semi-hemis on a new build and made them end flush with the outside edge of the bindings, but it doesn't feel right.…

I have a 74' D-28 im working on, just curious what you guys do in terms of process steps. Right now, im setting the angle, without frets(I reinforced the square tube rod with carbon fiber and will need to refret once put back together.) Do you guys shoot for the straight edge hitting the top of the bridge with, or without frets? Im wondering if I should undershoot my bridge just a touch so that then I can fret and have a good saddle hei…

I added measurements for the Yamaha FG red label FG 75's some time ago. I Keep getting these in for neck resets. I wanted to add photo's from the first one because they show that the dovetail joint does not align with the first fret beyond the neck/side to make folks aware so that one knows to slightly angle the drill to hit the pocket. I do the same on the holes drilled at the fret at the side/neck fret. I slightly angle the drill…

Hey lads I'm in a bit of an indecisive spot with a 70's yamaha acoustic refret. Pulled the original frets and the tang is .018" with no barbs just divots pressed into the lower edge. The slot is measuring .018". Struggled to find any suitable sized fretwire in stock in the UK that match what the customer wants that'll fit in the slot. Sintoms looked ideal but couldn't find any, so went with something with 0.20 tang and they're not pressi…

A Gagliano Jumbo probably made by Kay in the 1950's. It looks like this had a previous neck reset based on the shims and some sloppy chisel work. I removed the 14th and 15th frets because I had read that these might have a straight tenon. I didn't need to drill any holes for heat, as the spruce shims both split in half after the fretboard extension was released. The dovetail is about 11mm long, the pocket is 14mm deep, and the 15th fret…

Does anyone have a STL for a routing template that will sit square on a les paul body? I need to cut a P90 hole into a middle position, and it would be nice to use the router, rather than chiseling the edges...

Hello, One of my commissions is coming down the pike and it's going to be my first time using bar frets. I could use a once over for any helpful tips if you have any. About the guitar: Aged HD-28 but mahogany back and sides. I think Martin called this a HD-28 M? Skipping the truss-rod and using two carbon fiber strips. My process for Frets: 1: I CNC my fingerboards to a 16" radius and for T-frets I use a .023" to cut slots with a mat…

can anyone help me determine the neck angle on a 12 fret to the body neck Robbie Obrien says the gap betwwen the plane of a 14fret neck and the top of the soundboard at the bridge should be3.5 mm. does that hold true for 12 fret necks

Hello, I replaced a nut with a tusq nut. Nut slot height is correct, neck relief is good, action is good. But I’m still getting buzzing on low E and A strings on frets 1-3 primarily. I checked the fret height on fret 1 and it is sitting lower in that area specifically .038 inches. Vs .040 inches for the rest of the frets. I’m thinking this is what’s causing the buzz. Is my thinking correct? Is there something I can do other than a fret lev…

I cut the fret slots for a baritone guitar build today, so I thought I'd share my method for cutting fret slots, as I think it is a bit unusual. I radius and profile my fretboard before I cut the slots. I print out a paper layout of the fretboard, double-stick tape it to the radiused and profiled fretboard, line up the saw by eye to using red hatch marks on the printout, and saw the fret slots with a 3" circular saw that rides on…

I just pulled the neck off a Vega Arthur Godfrey Solo Lute baritone ukulele. It was pretty easy. First I heated and loosened the short fretboard extension. I already knew the neck was attached with a glued butt joint and small straight tenon. The picture show where I drilled three holes for foam cutter heaters. I only used the two on either side of the tenon, at the 16th fret (Note: neck joins body at 16th) and didn't need the hole at…

Hi everyone! I'm trying to wrap my head around this problem. I was doing some fret on a throwaway neck and found a couple of uneven frets in the middle of the neck. (I made sure to seat them down before levelling too!) While levelling, I came across an issue where the first few frets and the last few frets were being sanded down before the middle frets. I did make sure the neck was straight with a notched straight edge and the StewMac n…

YouTuber has been developing this for a while. I thought I would share it here. https://m.youtube.com/watch?v=X6RLN-sLtVA&pp=ygUQdGhlIG5leHQgcHJvamVjdA%3D%3D

Hi everyone - I recently ran into trouble making new nut for one of my necks that needed to be trued and re-fretted. I roughed in the nut as usual and then, with the bass guitar fully assembled and strung up, I started cutting the slots to depth. I use the StewMac digital nut slot depth gauge and have had good results in the past. I marked the nut's lowest points (radiused) using the guitar nut scribe tool (first time using this!) and c…