-
Kaur Kukkur posted a new loothprint. 3 months ago
AUK tools router top-to-side air vent conversionSimilarly to the Jessem router design, the idea is to have the router venting air stream not interfere with the dust collection going in the…
1 Comment-
Awesome !
-
-
James Roadman posted a new loothprint. 3 months ago
Truss Rod Helper Cauls for the SM Understring Leveling BeamThese are an adaptation by Dave Fils of Dan Erlewine’s trick of using a long beam, cauls, and a clamp to gently assist a neck…
-
Chip Tait Brooklyn Fretworks started the discussion Cool supplier shoutout: International Violin in the forum Quick Questions 3 months ago
Cool supplier shoutout: International Violin
I’m not sure how many folks around here are familiar with International Violin, but everyone should give them a look. They are a family business located in Baltimore, and they actually answer their telephone. They added a good number of fretted instrument tools and parts after LMI closed down. I just grabbed a bunch of micromesh sticks…
-
Ian Davlin The Looth Group replied to the discussion 72 Fender thineline frets removal in the forum Quick Questions 3 months ago
Reply to 72 Fender thineline frets removal
Where do you live ? If you’re close to NYC, I could take a look at it with you.
-
Marcus Chiang started the discussion 72 Fender thineline frets removal in the forum Quick Questions 3 months ago
72 Fender thineline frets removal
Hi everyone, I met a really hard one. Real 72 fender thineline refret. I removed the frets sideway super easy from 1 to 12 frets. But after 13 I almost destroy the frets and hurt the wood then fret just came out a little bit. And the frets are super low to be pull out. Please someone help me…
-
Gerry Hayes Haze Guitars replied to the discussion amp hum/buzz, single coils, and grounding in the forum Quick Questions 3 months ago
Reply to amp hum/buzz, single coils, and grounding
Hmm. Hard to say with any certainty but maybe the environment is a little noisy there. If you’re up for experimentation, you could try turning off electrical things and see if any makes a difference. Other than that, the shielding and replacing wiring with shielded cables certainly won’t hurt and is worth a try if you’re happy to put the time in.
-
Reply to Getting perfectly flat without a jointer
Good advice, as usual. I actually went back and tried to re-level the planer’s infeed and outfeed foldable ledges — very hard to do perfectly because they are fundamentally at slightly different planes. But I made a few cuts and it seems better already. Will try to fine tune it and see if I end up with something good.
I also wonder if I’m…
Danny West West Guitarworks -
<div>Kapton polyamide Heat resistant tape.</div><div>Combined with heat resistant soldering matts, can help as a heat sink to protect finishes from getting scored.</div><div>
</div><div>The tape is to line the matt with, not to stick onto guitar finish as it’s high tack. </div><div>
</div><div>The matts are usually made from fibre glass so ideally… Read moreplumbingsuppliesdirect.co.uk
Soldering Mats | Rothenberger Protection Soldering Mats
Soldering mats, also referred to as solder mats, are indispensable tools for individuals using soldering irons or blow torches.
Danny West West Guitarworks -
Hello,
Help needed please! 🙏
It’s a Washburn g10v that I am trying to source parts for.
The owner wants to do a full restore but we can’t move forward with the job as the trem is missing the micro tuner thumb nuts.
The trem is a big old rare thing with 2001 on the edge of it.
Please see picture for reference.
(Taken from reditt, a common problem it…
-
Reply to Black Grain Filler Under EM6000?
I have been using water based filler over sealer: sealer/ black filler/ sealer/ lacquer. I may just give that a test, (but with WB lacquer) but I would love to seal my purfling lines with epoxy. My last build was a nightmare with tiny “invisible” gaps that I couldn’t see until lacquer. I could barely see them afterward with a visor + loop. …
- Load More
![Profile photo of Danny da Cruz [da Cruz Guitars]](https://loothgroup.com/wp-content/uploads/avatars/0/674d94a777132-bpthumb.jpg){kind=avatar}
