Shopping Cart

No products in the cart.
The Looth Group
The Looth Group

loothgroup.com

featured videos

Wipe on Finish with Fill N Finish Ultra Thin
Wipe on Finish with Fill N Finish Ultra Thin
Tutorial on effective application of Fill n Finish Ultra Thin CA as a quick, good looking finish…..
Click Here
Iris Carr Restoration AMA
Iris Carr Restoration AMA
Iris Carr going over repair techniques and varnish retouch techniques. Very high level. ….
Click Here
Total Vise Sponsored Event
Total Vise Sponsored Event
The Looth Group has its first sponsor! Doug and Dan have long had a productive relationship with Jeff Howard (Total Vise) leading to such innovations ….
Click Here
ABC: Wood Torrefaction w/ Dana Bourgeois
ABC: Wood Torrefaction w/ Dana Bourgeois
Raw or cooked? While the age old discussion between air and kiln dried woods for guitar building rages on, the industry has moved on to treating wood ….
Click Here
From Fear to Fuel: Turning Anxiety into Progress in Lutherie
From Fear to Fuel: Turning Anxiety into Progress in Lutherie
Click Here
João Cassias with Robbie O’Brien
João Cassias with Robbie O’Brien
Passionate archtop builder, João Cassias, is joined by Robbie O’Brien in his shop in Brazil…..
Click Here

featured articles

Using acrylic to mimic a celluloid pickguard
Using acrylic to mimic a celluloid pickguard
After consulting with Ian Davlin, Doug Proper and a few others on the Loothalong, I looked into a celluloid solution. The materials were more expensiv….
Click Here
More Blast For Your Money
More Blast For Your Money
When the post is released from the chuck, the jaws are tightened shut and then used to press the anchor tightly into the body with a bit of hide-glue ….
Click Here
French Polishing For Luthiers with Eugene Clark
French Polishing For Luthiers with Eugene Clark
French polishing appealed for many reasons, especially the hardened versions of shellac. But what I needed to do was improve my technique – having fin….
Click Here
Martin Binding Repair
Martin Binding Repair
Reattaching loose bindings on acoustic guitars is a repair that one may initially think is a simple job. Still, the process can be more complex than a….
Click Here
Conflict Avoidance
Conflict Avoidance
Although there are some who do, most of us prefer not to have conflict in our lives. Conflict causes stress and can lead to other problems like lower ….
Click Here

featured loothprints

Surface Inspection Light
Surface Inspection Light
This Surface Inspection Light is designed to assist during the final sanding stage. It casts a raking light across the guitar’s surface, highlighting ….
Click Here
Fret End Bevel Jig
Fret End Bevel Jig
I use this jig when I want to bevel frets prior to installation. It has a 10-32 x 3/4″ Button Head Cap Screw to adjust the bevel and from 27-33 degre….
Click Here
optivisor adjustable LED clip
Optivisor adjustable light clip
Optivisor adjustable light clip
Click Here
3d Printed Bridge Pin Pullers
Pin Puller V2
Pin Puller V2
A simple 3D print to turn the Stewmac Fret Pullers into Bridge Pin pullers. Great way to get more use out of an expensive too. ….
Click Here
Stewmac Depth-Stop Drill Bits Holder
Stewmac Depth-Stop Drill Bits Holder
Caddy for holding the Stewmac depth stop drill bits. ….
Click Here

Report

Harassment or bullying behavior
Contains mature or sensitive content
Contains misleading or false information
Contains abusive or derogatory content
Contains spam, fake content or potential malware

Block Member?

Please confirm you want to block this member.

You will no longer be able to:

  • See blocked member's posts
  • Mention this member in posts
  • Invite this member to groups
  • Message this member
  • Add this member as a connection

Please note: This action will also remove this member from your connections and send a report to the site admin. Please allow a few minutes for this process to complete.

Report

You have already reported this .